MPL系列是針對印刷高亮光產品之表面印刷而開發的油墨，屬雙組份，高亮光，在加入5-10% 專用固化劑后，印刷品附著力更優，可通過百格、耐膠粘及指刮測試。 [通用性]：可用于絲印，移印（需添加相應的溶劑） [印刷范圍]：電鍍制品（鍍鋅、鍍銀、鍍金、鍍鈦）、金屬制品、玻璃等硬質塑料有良好的附著力。 [性能特點]：高亮光（可提供啞光型），高硬度，雙組份，色澤鮮艷，流平性好，高遮蓋力，耐溶濟，附著力優。 [干燥條件]： 1、自干，表干需15-30分鐘，實干需3小時以上（因氣候及印刷環境不同有差異），測試在油墨干燥后48小時后進行 2、烘烤：100-120度烘干及風干15-20分鐘，可達完全干透，60-80度烘干及風干30-40分鐘，可達完全干透 [技術參數]： 檢驗項目 檢驗結果 測試條件 油墨細度 ≤8um 刮板細度計 干膜光澤 ≧85° 60°鏡面光澤劑 附著力 100/100 1mm×1mm×100格 3M膠紙剝離 耐 磨 性 無變化 500g/5cm2負載含砂橡皮×200次來回 耐酒精性 無變化 500g/ cm2 負載99.5﹪酒精棉×500次來回 耐堿性 無變化 浸泡5%NaOH×24Hr 耐鹽性 無變化 浸泡5%NaC1×24Hr 耐水性 無變化 浸泡自來水×96Hr 耐熱性 無變化 250℃×5ETc [使用方法]：a. 使用前請將油墨充分攪拌均勻，以防止油墨中添加的助劑可產生分離現象。 b. 印刷前有必要可首先考慮除去印刷表面的油漬及塵埃。 c. 請根據作業實際環境條件合理選取本公司之配套稀釋劑。 d. 請根據印刷的理想效果，正確選取合適網版：250-380目網紗的網版，膠刮：65-90度耐溶劑膠刮。 [注意問題]： a. 本系列油墨必須搭配一定比例的硬化劑才能反應成膜，按主劑/硬化劑5-10%比例配制并攪拌均勻后，好是先固化10分鐘，再行添加稀釋劑以調整到印刷粘度。 b. 本系列油墨可選擇自干或烘烤兩種干燥方式,待工件冷卻后再行測試；自干需待印刷后24或48小時測試。 c. 不同的干燥方式需要的固化時間差異較大，其表現出來的涂膜性能也有一定差異，請根據自身實際條件確立優秀方式。 d. 多色套印時，初底層及中間層只需表干即可印刷下一顏色，后一色印完后，建議加熱固化。 e. 25℃條件下混入硬化劑后油墨可使用時間為6Hr，超過此時限，品質將有所影響，建議每批次配制量以六小時內用完為準。 以上油墨經SGS檢測符合歐盟ROSH標準. 敬告：以上資料記載為本公司實驗室資料數據，僅供參考，不作擔保和承諾，請在充分測試后加以使用。The MPL series is developed for printing on the surface of high gloss printing products. It has two components and high gloss. After adding 5-10% special curing agent, the adhesion of printed matter is better. It can be tested through 100 gram, sticky and finger scraping. [generality]: can be used for screen printing, imprinting (to add the corresponding solvent) [printing range]: electroplated products (galvanized, silver, gold-plated, titanium plating), metal products, glass and other hard plastics have good adhesion. [Characteristics]: Gao Liangguang (available in matte), high hardness, two-component, bright color, good leveling, high covering power, solvent resistance, excellent adhesion. [dry condition]: 1, self drying, it takes 15-30 minutes to dry the table. It takes more than 3 hours (different weather and printing environment). The test is done 48 hours after the drying of the ink. 2, baking: 100-120 degrees drying and air drying for 15-20 minutes, up to completely dry, 60-80 degrees drying and drying for 30-40 minutes, up to completely dry [technical parameters]: Inspection project Test results Test conditions Ink fineness Less than 8um Scraper fineness meter Dry film gloss More than 85 degrees 60 degree mirror gloss agent adhesion 100/100 1mm x 1mm x 100 lattice 3M adhesive paper stripping Wear resistance unchanged 500g/5cm2 loaded sand rubber * 200 times back and forth Alcohol resistance unchanged 500g/ cm2 load 99.5 alcohol cotton * 500 times back and forth Alkali resistance unchanged Soak 5%NaOH x 24Hr Salt tolerance unchanged Soak 5%NaC1 x 24Hr Water resistance unchanged Soak the tap water and 96Hr Heat resistance unchanged 250 c * 5ETc [use method]:a. before use, please stir well the ink well, so as to prevent the addition of additives in the ink to produce separation. It is necessary to first consider the removal of oil stains and dust on the printed surface before B. is printed. C. please select the company's supporting diluent according to the actual environmental conditions. D. according to the ideal effect of printing, select suitable screen: 250-380 mesh screen mesh, squeegee squeegee of solvent: 65-90. [attention problem]: A., this series of ink must be matched with a certain proportion of hardeners to form the membrane. According to the ratio of the main agent / hardener 5-10%, it can be prepared for 10 minutes before adding the diluent to adjust the printing viscosity. B. This series of ink can be selected to dry or bake two drying methods, when the workpiece is cooled and tested again; self drying needs to be printed 24 or 48 hours after the test. C. different drying methods need different curing time. The film performance is also different. Please establish excellent ways according to their actual conditions. D. polychromatic printing, the first floor and the middle layer only need to print the next color, after the first color printing, it is recommended heating curing. When E. is mixed with hardener at 25 C, the time of use of ink is 6Hr, which will affect the quality beyond this time limit. It is recommended that the volume of each batch should be used within six hours. The above ink is tested by the European Union ROSH standard by SGS. Notice: the above records for the company laboratory data for reference only, not a guarantee and promise, please be used in full after the test. [本信息來自于今日推薦網]